<p>This article presents the results of interlaboratory comparisons in which the RSE "Kazakhstan Institute of Standardization and Metrology" (KazStandard) participated within the framework of the Euro-Asian Cooperation of National Metrological Institutions (COOMET). The article discusses the organization of bilateral pilot comparisons of national standards for the kinematic viscosity of liquids …
<p>The article discusses the design schemes of devices for studying grain strength under dynamic loads. The main attention is paid to copra, which provide low-speed mechanical impact. Two types of coper are described: pendulum and with a falling load. These studies are important for the development of new methods and …
<p>This article discusses the important role of the introduction of automated environmental monitoring systems for emissions of pollutants into the atmosphere in the Republic of Kazakhstan, their advantages and disadvantages. The main components of automated monitoring systems are presented, and practical approaches to their selection and stages of implementation at …
<p>This article discusses a method for increasing the accuracy of indirect measurements of direct current strength using symmetric observations. The relevance of the study is the need to enhance the reliability and accuracy of measurement systems in the context of various external factors affecting the measurement results.</p><p>The paper presents an …
<p>The article is based on the analysis of the current state of conformity assessment of the organic production process, taking into account the results of the study of the Latvian organic production control system within the framework of the TAIEX INTPA project. The article is aimed at a wide audience, …
<p>The article discusses some aspects of national and interstate standards applied in the territory of the Republic of Kazakhstan. When comparing them, the similarities and differences of the general provisions of national and interstate standards for measuring gas humidity and the main prerequisites for the emergence of discrepancies between them …
<p>The article presents the results of an analysis of the fulfillment of the requirements of the technical regulations of the Customs Union «On Grain Safety» (TR CU 015/2011), approved by the Decision of the Customs Union Commission dated December 9, 2011 No. 874, by domestic enterprises and the implementation of …
<p>The article examines key aspects of compliance with product packaging standards in the context of globalized trade and the development of supply chains. Particular attention is paid to the requirements for packaged products in the United States of America, including an analysis of the legislative norms regulating this process. It …
<p>Within the framework of COOMET in the field of «Photometry and Radiometry», comparisons are planned on the spectral coefficient of directional transmission and the wavelengths of a spectrally selective transmission material. National standards in the field of optical and physical measurements of the Russian Federation, the Republic of Belarus, and …
<p>GLOBALG.A.P. (Global Good Agricultural Practice) certification is an international system of standards aimed at improving food safety, environmental protection, and working conditions in agriculture. This article explores the impact of GLOBALG.A.P. standards on various aspects of agriculture and discusses the key benefits and challenges of implementing this certification.</p><p>The scientific significance …
<p>This article discusses the calibration process of pipette dispensers, taking into account the uncertainty of measurements. The main purpose of the study is to determine the deviation of the dosed volume from the nominal control value. Metrological reliability, including the assessment of the uncertainty of the obtained measurement results, is …
<p>The article presents an analysis of the technical regulations of the Republic of Kazakhstan "On the safety of buildings and structures, building materials and products", approved by Order No. 435 of the Minister of Industry and Infrastructure Development dated June 9, 2023. The main aspects of this NPA, requirements including …
<p>The article examines the current problems of regulation of packaging products in Kazakhstan. It highlights the main requirements for packaging products, including packaging rules, labeling, as well as shortcomings in the legislation of the Republic of Kazakhstan regarding packaging products. Special attention is paid to state control over compliance with …
<p>This article discusses the results of comparisons in which the RSE "Kazakhstan Institute of Standardization and Metrology" (KazStandart) participated within the framework of the Euro-Asian cooperation of state metrological institutions (COOMET). The article discusses the organization of bilateral pilot comparisons of state standards of liquid density between KazStandart and the …
<p>Pressure unit standards are measuring instruments necessary for reproducing, storing, and transmitting the size of a pressure unit. The correct choice of pressure standard is important to achieve a high level of measurement accuracy in various fields of economics, including industry, medicine, science, and engineering. This article discusses the main …
<p>Aerosol is a dispersion system consisting of small solid or liquid particles suspended in a gaseous medium. Simply put, an aerosol is a suspension of particles in the air, such as dust, smoke, or fog.</p><p>Key characteristics of aerosols:</p><ol><li>Dispersion System: An aerosol consists of two phases: the dispersed phase (solid or …
<p>This article provides information on the development of measurement methods, and, based on them, interstate standards designed to measure product safety indicators for compliance with the requirements of the technical regulations of the Eurasian Economic Union, and the assessment of compliance of technical regulation facilities with the requirements established for …
<p>The article examines the impact of Regulation No. 870 on the application of international standards in Kazakhstan. Rules No. 870, adopted within the framework of the Law "On Standardization", play a key role in simplifying the process of integrating international standards, reducing administrative barriers, and increasing transparency of application. The …
<p>In recent decades, with increasing globalization and an increasing number of religiously oriented consumers, Halal product certification standards have become increasingly important. GSO 2055-1 / UAE.S GSO 2055-1 and OIC/SMIIC 1 standards play a key role in ensuring product compliance with Halal requirements. This article examines the principles and practical …
